Skip to Primary Navigation Skip to Site Navigation Skip to Main Content All 3M.com Site Map

3M™ Glass Bubbles for Subsea Insulation

Cross Section of 3M Glass Bubble Microsphere for Insulating Subsea Pipeline

At the low temperatures and high pressures encountered in deepwater environments, hydrates and asphaltenes can quickly form deposits that clog flowlines. Syntactic foam insulation made with 3M™ Glass Bubbles is a proven, cost-effective solution for maintaining temperature in subsea pipelines and risers, to help prevent deposition and scaling.

3M glass bubbles are inert, hollow glass spheres that are compatible with commonly-used components of subsea insulation and buoyancy systems. They are virtually insoluble in water – providing excellent utility in offshore applications. Any 3M glass bubble can be surface-treated with silane glass treatments to enhance bonding with the resin and to minimize a foam’s water pickup at high pressures. Glass bubbles are far more resistant to damage from elevated temperature, pressure and chemicals than alternative syntactic bead materials. Their low surface area per volume ratio makes high syntactic foam load levels possible.

High-strengh, low-density hollow glass microspheres for critical deepwater components (PDF, 771 Kb)

3M™ Glass Bubbles Applications

Subsea flowline cutaway to show insulation

Conventional flowline constructions, such as "pipe-in-pipe," are proving to be impractical and too costly for use at today's greater depths of 10,000 ft (3,000 m) and more. Although pipe-in-pipe offers the best U-value (insulating value) and longest cool-down times, the added weight and bulk of its construction can make it more difficult and costly to lay, and too heavy to support in deeper waters, of particular concern for risers.

As an alternative, flexible flowlines -- consisting of a single pipe coated with 3M glass bubble-filled syntactic foam insulation -- is less than half the weight of pipe-in-pipe, making it more practical for use at greater depths and in longer runs. Because this construction reduces overall pipeline subsea diameter, more pipe can be wound per spool, requiring fewer and smaller ships -- making installation faster, easier and more economical. Because of these and many other factors, wet pipe insulation now accounts for the majority of all new deep water subsea flowlines. Compared with the standard 3M glass bubble range of products, the XLD range of 3M glass bubbles allows thinner insulation on flexible subsea flowlines with the same insulation performance which enables even more pipe on a reel.

View Reprint of Offshore article “Wet insulation evolves to meet subsea flowline performance demands.” Rob Hunter, 3M Oil & Gas Business. 2008.

Subsea riser cutaway

The industry trend for deeper offshore oil production platforms has driven increasing use of wet insulation syntactic foam coatings made with 3M glass bubbles on Steel Caternary Risers (SCRs), Top-Tensioned Risers (TTRs) and riser towers, to achieve OHTC (U values) of 2 W/m^2 K and below.

At today’s greater depths, flexible flowlines made with 3M glass bubble-filled syntactic foam insulation offer a more practical, light weight alternative to conventional pipe-in-pipe constructions.

Glass Bubble strength measurement table

This table represents a sampling of the 3M glass bubbles portfolio of products suitable for syntactic foam insulation.

View 3M™Glass Bubble Strength Comparison Chart (PDF 54Kb)

Optimal flowline conditions chart

Optimal Performance Conditions

This graphic is intended to provide a rough visual guide to the conditions where they may provide the optimal balance of performance and cost.

For example, the U-values of syntactic foams formulated with 3M glass bubbles generally range from 2-12. While PiP can get down to 0.5 U-value, it comes at a much higher cost of material and installation -- so if higher U-values can be accommodated, wet pipe insulation can provide a lower cost alternative.

 

Need Help?

If you have questions or want more information, please
Contact Us.

Events

Offshore Technologies Conference

May 5-8, 2014
Houston, TX USA
Visit 3M Booth #5617
3M.com/OTC

Offshore Technologies Conference

May 5-8, 2014
Houston, TX USA
Visit 3M Booth #5617
3M.com/OTC

Global Petroleum Show

Calgary, AB
June 10-12, 2014
Visit 3M Booth #1110